CLECEM
@CLECEM_UV
Followers
363
Following
1K
Media
98
Statuses
218
#CLECEM is a research group of the @UV_EG focused on the development of #novelmaterials for #AnalyticalChemistry. Also on Instagram
Joined May 2020
Happy to share our lastest work ( https://t.co/d3upwfhdkh), where we prepared aptamer sorbents in polypropylene tubes for BPA extraction
0
0
5
👨🏫 Prof. Casado-Carmona (@FRYTHEPRO) delivered an oral presentation: “Enhancing membrane-based pipette tip extraction with 3D printing” 🔬 A collaborative work with @AS2P_RG and @CLECEM_UV.
1
3
9
Our member @Enrike7087 presented “3D PRINTING IN ANALYTICAL CHEMISTRY: REVOLUTIONIZING SAMPLE PREPARATION AND SENSORS” at @euroanalysis25 showcasing our contribution to 3D printing innovation in analytical chemistry #Euroanalysis2025 #Innovation #Sustainability
0
2
10
Our student @M_mrtzbriones has presented a poster entitled “Development of 3D-printed extraction devices modified with metal-organic frameworks for the analysis of marine toxins” at @euroanalysis25
#Euroanalysis2025 #AnalyticalChemistry #Sustainability
0
1
11
We are proud to share our advances in sample preparation at @euroanalysis25 through the oral presentation “Sorbent preparation using eco-friendly and waste-based supports: a step forward in sample preparation” delivered by @hectormperez3
#Euroanalysis2025 #AnalyticalChemistry
1
1
12
We are excited to take part in Euroanalysis XXII in Barcelona! The CLECEM group (@CLECEM_UV ) joins the international analytical chemistry community for a week of science, networking, and collaboration. #Euroanalysis2025 #CLECEM #ScientificCommunity #AnalyticalChemistry
0
1
17
Our last article, published in Analytica Chimica Acta, presents a 3D-printed rotating disk with MOF-coated chains for efficient extraction of viologen herbicides from rice, offering cleaner and faster analysis than conventional methods. https://t.co/biuR9JEc61
0
2
9
Finally, after the coffee break, we ended the Workshop with presentations by Ester Vázquez explaining hybrid hydrogels, and Rafael Gavara whose presentation explained antimicrobial packaging systems. Thanks again to the speakers for their presentations and to the attendees.
0
0
6
The second day began with Francisco Pena Pereira's presentation on low cost platforms. We continued with Miguel Moreno and Victor M. Gonzalez talking about aptamers, and ended the group with Elena Aznar whose presentation was about gated materials.
0
0
11
After the coffee break we continued with the presentation of Toni Iborra talking about different 3D printing technologies. And finally we ended the afternoon with Neus Crespí Sánchez, whose presentation was about tailored MOF-derived materials.
0
1
7
We started the Workshop with the presentation of Antonio Martín Esteban talking about the use of NADES. We continued with the presentation of Soledad Muniategui Lorenzo talking about microplastics in waters and ended with Roger Peró Gascón talking about mycotoxins in blood.
1
0
11
A week ago our CLECEM group held the 3rd workshop Advances in Sample Treatment Techniques and the 2nd workshop Advanced Materials in Low-Cost Platforms at the Faculty of Chemistry. We thank all the speakers and listeners for their collaboration and support.
0
2
10
0
0
4
🧪 3D-printed sensor containing a terbium-based MOF enables low-cost, solid-state fluorescence detection of tetracyclines in seawater & milk—no instrument mods needed! LOD: 0.5–1.8 µg/L. Cost: 1.60 €/unit. 🔗 https://t.co/rTR5eIAKb2
#3Dprinting #Sensors #MOFs
0
1
7
Thrilled to share the collaboration of @enrike7087 and Paula Molina with @ManuelMiro at @FITRACE_UIB. Spent an amazing week conducting cutting-edge research together. Thanks for the warm welcome, as always! #ResearchCollaboration
0
3
9
We developed an Aptamer-functionalized monolith on paper for selective lysozyme extraction in foods via TFME. Applied to egg-free & egg-based foods ✅Low-cost, reusable, and highly sensitive #FoodAnalysis #AnalyticalChemistry Work under @SamplePrepForce
https://t.co/SyVGl76Zer
0
2
11
La representación de CLECEM group quiere darle las gracias a @VeronicaPino_ y @jhdezborges78 @MAT4LL @AchemGroup por la excelente organización, y a @msolcar de @AS2P_RG. Ha sido un auténtico placer disfrutar de este final de workshop @In_SAmPr. Nos vemos pronto 😉👌
2
2
20
Our PhD students have presented in the National Network for sustainable sample preparation (@In_SAmPr) works about aptamer@monolith (@Natalia_Piq) and 3D-printed@MOF (@M_mrtzbriones) devices
0
6
23
Desde Valencia, @CLECEM_UV nos cuenta la modificación de monolitos con aptámeros y el uso de la tecnología de impresión 3D para el desarrollo de nuevos materiales. 😀😀
0
3
14